FREQUENTLY ASKED QUESTIONS
What makes the bit “Perfect?”
The pivot point is what makes them “perfect." All horses were started in a ring snaffle, so a horse understands pressure on the corner’s of their mouth. With the ball-joint, we have created that same feel that your horse has been trained in. The only reason why you go to a shank bit is to apply curb chain pressure. Different disciplines of riding require different lengths of shanks. Older horses require different bits than younger horses. Tough mouth horses require different mouthpieces than light-mouth horses, but our concept of two pressure points make it “perfect.” If they're "The Perfect Bit", why do you have so many different ones? We are so confident that they will not wear out that we offer a lifetime warranty on our bits. How long before the ball wears out? What length of shank do I need?
Just remember, the longer the shank the more pressure you are able to apply to the chin….which means more “whoa.” Does the bit have any copper? Yes, we the center joint has a bead of copper around it. Our bits are made of stainless steel with the center joints made of cold-rolled steel so it will rust and give your horse a familiar taste. The copper bead around it is there so there are 2 different metals to kick off salivation in your horse’s mouth. Will it pinch my horse’s mouth?
No. We guarantee it not to pinch. Before, we added the curb rings, we found out that if you had a horse with a wide mouth, the curb chain hits against the body of the bit could pinch part of the horse’s lip. To fix this problem, we added the curb rings to eliminate the chance of that happening, but the bit itself will not pinch. If we did have a port, it would not do anything because our mouthpieces do not move because of the ball-joint. No barrel racer, roper, or cutter, etc. should be riding a port. Ports are designed for headset only…they have absolutely nothing to do with “whoa.” If you are riding a tie-down and a port at the same time, one of them is not doing their job…they are designed for the same job. Do you have a ported mouthpiece? We have all heard the old saying, “1 finger, 2 fingers, etc.”, but just think about that….say we are riding the same horse, would we adjust the curb chain just because our fingers are not the same size? How I adjust my curb chain is to get beside my horse and push back on my shanks and when my horse takes a step back, that is how far my hands will travel before my curb chain comes into effect. So, depending on what you are doing on your horse and how much you want your hands to move before he starts to react to the curb chain is how loose or tight you will adjust your curb. And, remember, tightening your curb chain will not give you more “whoa” it only means your hands will have to travel less before the curb comes into effect. And, the smaller the curb, the more “bite” it will have. The wider the curb, the less effective it will be. If I have a horse that is fresh and not responding well with my normal curb, I will get a small curb (our sharp curb chain)…just to get his attention and then go back to my normal curb. How do I adjust my curb chain?
What is the purpose of the calvary shank?
The only purpose of the Cavalry shank is so that a horse cannot reach the shank with his lip. It breaks away from the body of the bit quicker than our original shank, so that the horse is unable to get the shank in his mouth and play with it. Our rings of the shanks come out in the exact same spot, only has a curve in the shank. Yes, the function of how our bit works will make perfect sense to every horse. And, the pressure points of The Perfect Bit is the same pressure points that all horses have been trained in since day one in a ring snaffle. Will it work on every horse? Yes, with a regular ring snaffle, when you pull back the center joints breaks down and pokes the roof of your horse’s mouth. With The Perfect Bit ring snaffle, the ball joint allow the mouthpiece to stay between the tongue and the roof of the mouth. And, with a regular ring snaffle when turn your horse it will open all of the way out, but with "The Perfect Bit" ring snaffle, the ball-joint only goes so far out and you immediately start moving the other side….which causes the shoulders to move more quickly with the same range of motion with your hands. Does "The Perfect Bit" ring snaffle differ from a regular ring snaffle?
TOP

DESIGNED BY BIG CREEK PRODUCTIONS Copyright © 2014 - All Rights Reserved

perfectbit2003@yahoo.com

(918) 244-2222